Intex Graphite Grey Panel above-ground pool - rectangular - L400 x W300 x H124 cm

With the Intex Graphite Grey Panel above-ground pool L400 x W300 x H124 cm (10,091 L) you choose a luxurious & sturdy pool. So you can enjoy years of splashing fun in a safe & durable way.

The Graphite Panel pools are the luxury horses in the range of Intex. These pools come in a set with all kinds of accessories (sand filter pump, ladder, groundsheet & cover) so everything is there to take a refreshing dip within hours!

The Graphite Panel pool is not only very strong, but also looks incredibly luxurious thanks to the sturdy plastic panels. These panels have the look of wood thanks to the imitation grain, but the ease of maintenance of plastic. This sets the pool apart from all other above-ground pools. Moreover, the panels also provide extra protection for the solid liner & outside influences.

Moreover, the tubes of this pool have a powder-coated interior, unlike many other above-ground pools where only the outside of the tubes are powder-coated. Thus, the inside of the tubes are also protected from rust. This pool has a thicker 3-layer liner so it can take a beating.

The strengths of the Intex Graphite Grey Panel design pool at a glance:
- Luxurious appearance due to the imitation wood look
- Finished with high quality plastic panels, which also protect the liner
- Solid tube construction & three-layer "Super-Though" walls
- Powerful sand filter pump for clear & hygienic water


Supplied accessories

Powerful sand filter pump 4 m³
Of course, this luxurious pool also needs a powerful filter. This will keep your pool wonderfully clean. The Graphite Grey Panel pool comes with a sand filter pump. This pump uses filter sand or glass beads (not included) to filter the water. The big advantage of a sand filter pump is that it filters the water much more accurately than a cartridge filter pump. Moreover, you don't have to replace the sand every two weeks, which is the case with cartridges. That way you save a lot of effort & money in the long run!

This set includes a pre-filter that first filters the coarse dirt. The dirt is collected in the basket of the pre-filter for easy emptying. In addition, the sand filter pump also filters fine dirt. The sand filter pump has a capacity of 4 m³. This means that 4,000 L of water per hour is filtered.

The filter pump can run up to 8 hours per day. For best cleaning, we recommend running the pump 4 hours in the morning and 4 hours in the evening. This is also the ideal time to measure the pool values (pH, chlorine & alkaline) and add the necessary products. This way the pool is wonderfully clean before diving & is cleaned again after all the splashing fun. With the built-in timer, you can easily set when the pump should get going. So you can enjoy delicious & fresh water every day.

Tip from poolboy Marcel:
A pool not only provides cooling & fun but also requires maintenance. So keep a close eye on the pool values (pH, chlorine & alkaline values) in order to enjoy your pool safely and as long as possible. Not sure how to summer-proof your pool? Then be sure to read this blog article to get your pool ready for swimming in 5 steps.

Safety ladder
Swimming & splashing in the water is of course super fun, but we opt for safety first! A slip happens faster than you think. The sturdy ladder supplied makes it easy and safe to get in and out of the pool. Moreover, the front part of the ladder can be folded upwards to prevent small daredevils from climbing into the pool. The ladder is very easy to assemble and the plastic steps will last for years.

Luxury cover
Finished splashing? Then close the outdoor pool with the supplied cover so it stays nice and clean for your next dip. A cover keeps falling leaves, twigs or other debris out of your clear water. Moreover, the water will also cool down less quickly with this cover. The tarp is perforated in the middle so the water does not stay on the tarp. With the nylon drawstring, you can easily attach the cover to the edge of the pool.

Our tip: prevent the cover from sinking into the water & place an inflatable tire under the cover on the water.

Want a pool that is always nice and warm? Then choose pool heating. With a heat pump or mat, you can easily heat the water a few degrees. Put a solar cover on the pool to keep the water warm longer too & let the pool naturally heat up from the sun. This cover has an insulating function and partially protects your pool from dirt. Because the solar cover floats on the pool (and is not fastened over the edges of the pool), dirt can still get into your pool along the sides of the cover. So this is not an alternative to a cover.

Ground sheet
The ground cover keeps the bottom of the pool clean. This saves you a lot of cleaning work when storing your pool in the fall!
Want extra protection for the underside of the pool? Then choose floor tiles - suitable for both garden and terrace.

Repair kit
Due to the enthusiastic splashing & the many water games, an accident can always happen. This set includes a handy repair kit.


Setting up the Graphite Grey Panel Pool
This pool is a real crate-pusher with luxurious looks, but also requires a bit more time to set up. Count on about two hours with 2 people.
In the package is a comprehensive manual that tells you step by step how to assemble the pool (without extra tools). We like to list it for you:

Step 1: Pick a spot with a flat and level surface. Allow at least 1m extra space around the pool for accessories, such as the filter pump.

Step 2: Remove pebbles, twigs or other sharp objects that can damage the pool.

Step 3: Provide a solid surface and lay down pool tiles if necessary. Are you using these tiles? If so, dig them in at ground level. If the ground is soft or sandy, the legs may sink, and the frame will not be as stable. Lay down the groundsheet.

Step 4: Spread the liner in the middle of the groundsheet. Place the frame parts in the correct position. Caution: do not drag the tubes or liner to avoid damage. Leave the liner in the sun for a while to make it more flexible, and sprinkle the tubes with talcum powder.

Step 5: First assemble the horizontal beams and corner legs, then assemble the U-shaped side supports.

Step 6: Check that the water drainage steps on the inside and outside of the pool are securely fastened. The tension flaps, U-shaped side supports/vertical legs should all be tightened and straight.

Step 7: Fill the pool with 3cm of water to check that the pool is level and has no leaks. The folds on the bottom should be made as smooth as possible. This can be done by pushing the fold from the inside out where the wall & bottom meet. Do this only with bare feet!

Step 8: Once the pool is filled, you can proceed with the assembly of the pool enclosure. To do this, follow all the steps in the manual carefully.